发布时间:2023-08-16
COMBINATION METHODS
A weighing system contains a stationary type weighing module, a semifloating type weighing module and some floating type weigh module. Standard combination:
1. a kit of four modules: one stationary type, one semifloating type and two floating type modules.
2. a kit of three modules: a stationary type, a semifloating type and a floating type module
INSTALLATION REQUIREMENTS
1. The flatness of each weighing module’s foundation should be less than 0.3mm. All foundations should be in the same horizontal plane and the flatness among them is required between 0-3mm.
2. The flatness of bearing surface connected with the weighing module should be within 0 .3mm . All bearing surfaces should be in the same horizontal plane and the flatness among them should be between 0-3mm.
NOTES OF INSTALLATION
1. The semi-floating module should be kept away from the fixed module as far as possible.
2. Connecting modules with foundations and bearing surface can use bolting or welding. In welding, pay attention to connect the welding machine with the ground. When welding the base board with foundation, the welding machine should be connected on the foundation, when welding the top board with and the bearing surface, the welding machine should be connected with ground on the bearing surface. Do not allow current go through the load cells to avoid any damage to load cells
3. After installing, loose the nuts on the top of the bolt to remove the sleeve from supporting board (released state as shown in picture)
组合方式:
在一个称重系统中,使用一只固定式称重模块,一只半浮动式称重模块,其余用全浮动式称重模块。标准组合为:
1. 四件套: 一只固定式,一只半浮动式,二只全浮动式模块
2. 三件套:一只固定式,一只半浮动式,一只全浮动式模块
SBT- FW称重模块安装基础要求:
1. 每一称重模块的安装基础的平面度应在0.3mm以内,各基础应在同一水平面上,其平面度要求在0-3 mm之间。
2. 与称重模块连接的支承面的平面度应在0.3mm以内,各支承面应在同一水平面上,其平面度要求在0-3mm之间。
安装注意事项:
1. 半浮动式模块的安装位置应尽量远离固定式模块。
2. 模块与基础及支承面的连接,可用螺栓连接或焊接。焊接时应注意焊机的接地,当模块底板与基础 焊接时,焊机应在基础上接地,当模块顶板与支承面焊接时,焊机应在支承面上接地。勿使电流通 过传感器,以免损坏传感器。
3. 安装完毕,应将图中支撑螺杆顶部的螺母松开,使套筒挚圈离开支撑板(图中所示为松开状态)。
NOTICE 注意
Top plate shall be safely grounded to avoid any possible current going through the load cell . (焊接时顶板应接地,不可使电流通过传感器。)
WARNING 警告
1. Adjustment, inspection and maintenance shall be done by professional persons .
2. The device shall be well grounded .
1. 请专业人员调试、检测和维修系统。
2. 请保持本设备良好接地。
NOTICE 注意
1. No hot plugging .
2. Power off before connecting, checking and repair- ing the device .
1. 严禁带电插拔。
2. 请先切断电源,再进行电气设备连接,检修。
2024-09
计重收费是车辆通过设置在收费站收费车道前端的动态称重装置、车辆分离装置、车型识别装置时,数据采集处理
2024-09
很多人通常把压力变送器,压力传感器误认为是一样的,都代表传感器,其实他们有很大的差别。一、压力丈量仪
2024-09
称重传感器实际上是一种将质量信号转变为可测量的电信号输出的装置。用传感器茵先要考虑传感器所处的实际工
2024-09
称重传感器的工作是通过准换被测物体的重力为电信号来达到精确测量的目的。称重传感器有很多种,那隆旅电子
识别二维码了解更多资讯
公司名称:数字传感器|模拟传感器|称重传感器|测力传感器|其他电阻应变式传感器|称重模块|称重仪表-[江西翼腾]专业传感器代理厂家
全国统一服务热线: 0792-8223700 13879291204
地址:江西省九江市开发区长城路121号恒盛科技园3号楼8楼808
联系:13879291204 李洁 13907028108 黄正健
地址:江西省九江市开发区长城路121号恒盛科技园3号楼8楼808
赣ICP备2020010441号-1 赣公网安备 36049002000141号